error erasing in jkeys jtag
ird # r 00 0006 5535-46 box keys: ff ff ff ff ff ff ff ff i click "yes". jkeys says at the bottom of the window "awaiting erasure completion", been on this for 6 days pulling my hair reading and reading and reading. lots of late
510 jkeys won't read
plugged in no lights come on, also not if try with front switch or remote, fan and disk runs. if i power up with oj1 jumped i get the green light on, if i put in a non working card the ird reads showing the normal error message
تعلم كل شئ عن الفضائيات وتحديث
5- قم بتشغيل البرنامج المرفق وهو jkeys عند عملية الكشف في النافذة السابقة وهي " error reading via dcu ird info مثل الموجود في النافذة التالية :
پر كردن فلش متاباكس با نرم افزار jkeys
<br /><br />اما ممكن است به محض اجراي jkeys به پيام خطاي زير برخورد كنيد: error reading from ird(dcu peek) اين خطا زماني رخ ميدهد كه آي سي فلش شما با cpu
pansat 2500 jtag help!!!
i have a pansat 2500 and i am trying to jtag it, but when i run jkeys.exe i get a message saying, "error reading from ird (dcu peek)." can anyone help me with this? thanks
امروز در مورد تمام error هاي برنامه jkeys
error reading from ird (dcu peek اين خطا زماني رخ ميدهد كه آي سي فلش شما با cpu رسيور ارتباط برقرار كرده در اين صورت برنامه jkeys نمي تواند به آدرسهاي
جیتگ متاباکس قسمت
در صورتی که برنامه ارور error reading from ird (dcu peek را ird model را بر روی 4900 بگذارید و برای پاک کردن فلش از http://satellite.ir15.com/upload/metabox/jkeys-2.9.10.zip
ø¬ûœøªú¯ ù…øªøø¨øú©ø³ ù‚ø³ù…øª
ø¯ø± øµùˆø±øªûœ ú©ù‡ ø¨ø±ù†ø§ù…ù‡ ø§ø±ùˆø± error reading from ird (dcu peek ø±ø§ ø¨ø¯ù‡ø¯ ûœø¹ù†ûœ ø§ûœù†ú©ù‡ ø¨ø±ù†ø§ù…ù‡ ù†øªùˆø§ù†ø³øªù‡ ø§ø³øª ø¨ø§ ø¢ûœ ø³ûœ ù ù„ø´ http://satellite.ir15.com/upload/metabox/jkeys-2.9.10.zip
full panel to 2300
trying to jtag for first time using jkeys had to edit jkey.def connected jtag as i opened and turned on receiver it gives me error reading dcu peek.i ignored that and went on i dont get box keys or ird# opened flash program could not
atmega n2 how to guide!!!!
what you will need: jtag, atmega, ird, jkeys and hex workshop or wonka may give you an error message about no signal. do a check switch! that should do note: if you try to read your atmega after it may appear you can not get in,
301.013 single tsop-need help to reprogram-new tsop-am29lv320dt
Am28lc320dt ” with jkeys . When I click flash programming get error message : Error reading from IRD ( DCU Peek ) can any one help or guide me to a link
jkeys won't read ?? - FTA - DSS Forum
Originally posted by kamkam1 1 . 2700 ird 2 . jtag 3 . jkeys 201 4 . ird plugged in keep getting error reading from DCU peek need help please
Fortec Files - al7bar, firmware, keys, downloads & more! - Jtag
I am using jkeys . exe and when i run the program I get an error saying , " Error reading from IRD ( DCU Peek ) . " Can anyone help me ?
WWW.PAKISTANI-FORUM.COM :: View topic - Jtag error message???
what is the reason if i get the following messages from Jkeys : 1 . error reading from IRD ( DCU peek ) ? 2 . error reading from memory ?
Bevkeys - Forum - TSOP (IRD) PROBLEMS - jtag port for 301.013 -
This is my first effort , but I think jkeys opened and read the box keys powed the IRD down then back up , but then crash with the error ' read error .
Fortec Files - al7bar, firmware, keys, downloads & more! - Jtag
I am using jkeys . exe and when i run the program I get an error saying , " Error reading from IRD ( DCU Peek ) . " Can anyone help me ?
WWW.PAKISTANI-FORUM.COM :: View topic - Jtag error message???
what is the reason if i get the following messages from Jkeys : 1 . error reading from IRD ( DCU peek ) ? 2 . error reading from memory ?
Bevkeys - Forum - TSOP (IRD) PROBLEMS - jtag port for 301.013 -
This is my first effort , but I think jkeys opened and read the box keys powed the IRD down then back up , but then crash with the error ' read error .
Bevkeys - Forum - TSOP (IRD) PROBLEMS - WAKE UP 3100 RECIVER
With Jtag still hooked up, start Jkeys 2.0.1 & let’s reflash Flash The problem i have is that i don ' t get the error which by reading seems like i
how to jtag megasat2700xl ? - Curious Contraptions Community
So log in, read the forums, share your knowledge and become a part of the but when i read it with jkeys first give me an " error reading from ird ( dcu
Fortec Ultra Jtag and not ""Error reading from IRD (DCU Peek)" any
Fortec Ultra Jtag and not " " Error reading from IRD ( DCU Peek ) " any more , very easy Turn On the recevier ; Open Wall ; Open Jkeys and :
Error reading from IRD DCU Peek
this is the first time I have to jtag my receiver it's a pansat 2500A clone, using jKeys 2.9.11 and I get Error reading from IRD (DCU Peek).
SRT jtag store - Page 3 - FunFiles Satellite Encryption
Have also tried other IRD options on jkeys with this flash ic but also had no If you see " error reading fron DCUcontrol register " , you have miss
|
